Bad problem with your car? Reduce smoke

but also a person not associated in any way with passion about cars or other vehicles also willing to peek at these cars. The car after renovation will attract the eyes of everyone in the vicinity. There is no doubt that this is

Dodane: 09-09-2016 19:12
Bad problem with your car? Reduce smoke best oil for Renault

Why restored old cars attract the eye?

More and more people are interested in really ancient models of cars. There is no shortage connoisseurs of such cars among the real car fans, but also a person not associated in any way with passion about cars or other vehicles also willing to peek at these cars. The car after renovation will attract the eyes of everyone in the vicinity. There is no doubt that this is a very good way to stand out in the environment around us. Although often these cars are very expensive and driving them is quite uneconomical, you can also treat it as an investment. It is true that we have obtained through this investment a quick profit, but in the long term we really expect lots of money - if not for us, if only for our children and grandchildren.


Automotive industry and economic impact

Around the world, there were about 806 million cars and light trucks on the road in 2007, consuming over 980 billion litres (980,000,000 m3) of gasoline and diesel fuel yearly.7 The automobile is a primary mode of transportation for many developed economies. The Detroit branch of Boston Consulting Group predicts that, by 2014, one-third of world demand will be in the four BRIC markets (Brazil, Russia, India and China). Meanwhile, in the developed countries, the automotive industry has slowed down.8 It is also expected that this trend will continue, especially as the younger generations of people (in highly urbanized countries) no longer want to own a car anymore, and prefer other modes of transport.9 Other potentially powerful automotive markets are Iran and Indonesia.10 Emerging auto markets already buy more cars than established markets. According to a J.D. Power study, emerging markets accounted for 51 percent of the global light-vehicle sales in 2010. The study, performed in 2010 expected this trend to accelerate.1112 However, more recent reports (2012) confirmed the opposite; namely that the automotive industry was slowing down even in BRIC countries.8 In the United States, vehicle sales peaked in 2000, at 17.8 million units.13

Źródło: https://en.wikipedia.org/wiki/Automotive_industry#Economy


Other systems are also used

On its bottom, the sump contains an oil intake covered by a mesh filter which is connected to an oil pump then to an oil filter outside the crankcase, from there it is diverted to the crankshaft main bearings and valve train. The crankcase contains at least one oil gallery (a conduit inside a crankcase wall) to which oil is introduced from the oil filter. The main bearings contain a groove through all or half its circumference; the oil enters to these grooves from channels connected to the oil gallery. The crankshaft has drillings which take oil from these grooves and deliver it to the big end bearings. All big end bearings are lubricated this way. A single main bearing may provide oil for 0, 1 or 2 big end bearings. A similar system may be used to lubricate the piston, its gudgeon pin and the small end of its connecting rod; in this system, the connecting rod big end has a groove around the crankshaft and a drilling connected to the groove which distributes oil from there to the bottom of the piston and from then to the cylinder.

Other systems are also used to lubricate the cylinder and piston. The connecting rod may have a nozzle to throw an oil jet to the cylinder and bottom of the piston. That nozzle is in movement relative to the cylinder it lubricates, but always pointed towards it or the corresponding piston.

Typically a forced lubrication systems have a lubricant flow higher than what is required to lubricate satisfactorily, in order to assist with cooling. Specifically, the lubricant system helps to move heat from the hot engine parts to the cooling liquid (in water-cooled engines) or fins (in air-cooled engines) which then transfer it to the environment. The lubricant must be designed to be chemically stable and maintain suitable viscosities within the temperature range it encounters in the engine.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine



© 2019 http://miasto.lebork.pl/